RexMag's Naughty Files Adult Discussion Board Rex is in the House

Board Photos Radio and TV Match Maker Reputations Points
Go Back   RexMag's Naughty Files Adult Discussion Board > Adult Humor > Jokes & Humor
Register Arcade Blogs FAQTop Posters Calendar Mark Forums Read


Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 01-18-2009, 06:14 PM
Hellsbells182's Avatar
Senior Member
Points: 12,250, Level: 26 Points: 12,250, Level: 26 Points: 12,250, Level: 26
Activity: 0% Activity: 0% Activity: 0%
 
Join Date: Aug 2003
Location: Dallas TX
Posts: 2,757
My Mood: Doh
Thanks: 2,121
Thanked 1,752 Times in 1,032 Posts
Hellsbells182 has a reputation beyond reputeHellsbells182 has a reputation beyond reputeHellsbells182 has a reputation beyond reputeHellsbells182 has a reputation beyond reputeHellsbells182 has a reputation beyond reputeHellsbells182 has a reputation beyond reputeHellsbells182 has a reputation beyond reputeHellsbells182 has a reputation beyond reputeHellsbells182 has a reputation beyond reputeHellsbells182 has a reputation beyond reputeHellsbells182 has a reputation beyond repute
Tool Definitions

Tool Definitions


DRILL PRESS: A tall upright machine useful for suddenly snatching flat metal
bar stock out of your hands so that it smacks you in the chest and flings your
beer across the room, denting the freshly-painted part which you had carefully
set in the corner where nothing could get to it.

WIRE WHEEL: Cleans paint off bolts and then throws them somewhere under the
workbench with the speed of light. Also removes fingerprints and hard-earned
calluses from fingers in about the time it takes you to say, ''What the...??''

ELECTRIC HAND DRILL: Normally used for spinning pop rivets in their holes
until you die of old age.

SKILL SAW: A portable cutting tool used to make studs too short.

PLIERS: Used to round off bolt heads. Sometimes used in the creation of
blood-blisters.

BELT SANDER: An electric sanding tool commonly used to convert minor
touch-up jobs into major refinishing jobs.

HACKSAW: One of a family of cutting tools built on the Ouija board principle.
It transforms human energy into a crooked, unpredictable motion, and the more
you attempt to influence its course, the more dismal your future becomes.

VISE-GRIPS: Generally used after pliers to completely round off bolt heads.
If nothing else is available, they can also be used to transfer intense welding
heat to the palm of your hand.

WELDING GLOVES: Heavy duty leather gloves used to prolong the conduction of
intense welding heat to the palm of your hand.

OXYACETYLENE TORCH: Used almost entirely for lighting various flammable
objects in your shop on fire. Also handy for igniting the grease inside the
wheel hub you want the bearing race out of.

TABLE SAW: A large stationary power tool commonly used to launch wood
projectiles for testing wall integrity.

HYDRAULIC FLOOR JACK: Used for lowering an automobile to the ground after you
have installed your new brake shoes, trapping the jack handle firmly under the bumper.

EIGHT-FOOT LONG YELLOW PINE 2x4: Used for levering an automobile upward
off of a trapped hydraulic jack handle.

E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times harder than any known drill
bit that snaps neatly off in bolt holes thereby ending any possible future use.

BAND SAW: A large stationary power saw primarily used by most shops to cut
good aluminum sheet into smaller pieces that more easily fit into the trash
can after you cut on the inside of the line instead of the outside edge.

TWO-TON ENGINE HOIST: A tool for testing the maximum tensile strength of
everything you forgot to disconnect.

CRAFTSMAN 1/2 x 24-INCH SCREWDRIVER: A very large pry bar that inexplicably
has an accurately machined screwdriver tip on the20end opposite the handle.

AVIATION METAL SNIPS: See hacksaw.

PHILLIPS SCREWDRIVER: Normally used to stab the vacuum seals under lids and
for opening old-style paper-and-tin oil cans and splashing oil on your shirt;
but can also be used, as the name implies, to strip out Phillips screw heads.

STRAIGHT SCREWDRIVER: A tool for opening paint cans. Sometimes used to convert
common slotted screws into non-removable screws.

PRY BAR: A tool used to crumple the metal surrounding that clip or bracket you
needed to remove in order to replace a 50 cent part.

HOSE CUTTER: A tool used to make hoses too short.

HAMMER: Originally employed as a weapon of war, the hammer nowadays is used
as a kind of divining rod to locate the most expensive parts adjacent the object we
are trying to hit.

MECHANIC'S KNIFE: Used to open and slice through the contents of cardboard
cartons delivered to your front door; works particularly well on contents such
as seats, vinyl records, liquids in plastic bottles, collector magazines,
refund checks, and rubber or plastic parts. Especially useful for slicing work
clothes, but only while wearing them.

DAMMIT TOOL: Any handy tool that you grab and throw across the garage while
yelling ''DAMMIT'' at the top of your lungs. It is also, most often, the next
tool that you will need.
__________________
Reply With Quote
The Following 3 Users Say Thank You to Hellsbells182 For This Useful Post:
dampa (01-19-2009), luvablenursexx (01-19-2009), mun (01-19-2009)
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Tool Definitions - With Tongue Firmly In Cheek pandora Jokes & Humor 0 07-25-2009 03:50 PM
Psp For Beginners A Good Read If New To It manictaz Help! Puter Tutors 0 06-18-2007 01:04 PM
VB's PSP Tutorial Thread Absolute BiOnyx Graphics & Art 40 03-13-2007 06:04 AM
Tool Glossary coot Jokes & Humor 0 03-12-2007 10:28 AM
A tool for all delboy2222 Funny Pictures 1 11-27-2006 07:21 PM


All times are GMT -4. The time now is 06:11 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
© 2002 - 2010 BN Media, LLC