RexMag's Naughty Files Adult Discussion Board Rex is in the House

Board Photos Radio and TV Match Maker Reputations Points
Go Back   RexMag's Naughty Files Adult Discussion Board > Adult Humor > Jokes & Humor
Register Arcade Blogs FAQTop Posters Calendar Mark Forums Read


Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 12-11-2008, 11:06 AM
weemo05's Avatar
Cya in my dreams
Points: 46,918, Level: 52 Points: 46,918, Level: 52 Points: 46,918, Level: 52
Activity: 0% Activity: 0% Activity: 0%
Snake Champion, Trampoline Tricks 2 Champion, Zookeeper Champion
 
Join Date: Mar 2005
Location: In your dreams
Posts: 7,494
My Mood: Amused
Thanks: 16,576
Thanked 5,081 Times in 1,803 Posts
weemo05 has a reputation beyond reputeweemo05 has a reputation beyond reputeweemo05 has a reputation beyond reputeweemo05 has a reputation beyond reputeweemo05 has a reputation beyond reputeweemo05 has a reputation beyond reputeweemo05 has a reputation beyond reputeweemo05 has a reputation beyond reputeweemo05 has a reputation beyond reputeweemo05 has a reputation beyond reputeweemo05 has a reputation beyond repute
common tools explained

To the unitiated, the workshop can be an intimidating place, full of tools you may not know what to do with. To help, here's a helpful explanation of common tools and their uses.

DRILL PRESS:
A tall upright machine useful for suddenly snatching flat metal bar stock out of your hands so that it smacks you in the chest and flings your beer across the room, denting the freshly-painted vertical stabilizer which you had carefully set in the corner where nothing could get to it.
WIRE WHEEL:
Cleans paint off bolts and then throws them somewhere under the workbench with the speed of light . Also removes fingerprints and hard-earned cleco calluses from fingers in about the time it takes you to say, "Oh sh*t!"
ELECTRIC HAND DRILL:
Normally used for spinning pop rivets in their holes until you die of old age.
SKILL SAW:
A portable cutting tool used to make studs too short.
PLIERS:
Used to round off bolt heads. Sometimes used in the creation of blood-blisters.
BELT SANDER:
An electric sanding tool commonly used to convert minor touch-up jobs into major refinishing jobs.
HACKSAW:
One of a family of cutting tools built on the Ouija board principle. It transforms human energy into a crooked, unpredictable motion, and the more you attempt to influence its course, the more dismal your future becomes.
VISE-GRIPS:
Generally used after pliers to completely round off bolt heads. If nothing else is available, they can also be used to transfer intense welding heat to the palm of your hand.
WELDING GLOVES:
Heavy duty leather gloves used to prolong the conduction of intense welding< /SPAN> heat to the palm of your hand.
OXYACETYLENE TORCH:
Used almost entirely for lighting various flammable objects in your shop on fire. Also handy for igniting the grease inside the wheel hub you want the bearing race out of.
TABLE SAW:
A large stationary power tool commonly used to launch wood projectiles for testing wall integrity.
HYDRAULIC FLOOR JACK:
Used for lowering an automobile to the ground after you have installed your new brake shoes, trapping the jack handle firmly under the bum per.
EIGHT-FOOT LONG YELLOW PINE 2X4:
Used for levering an automobile upward off of a trapped hydraulic jack handle.
E-Z OUT BOLT AND STUD EXTRACTOR:
A tool ten times harder than any known drill bit that snaps neatly off in bolt holes thereby ending any possible future use.
BAND SAW:
A large stationary power saw primarily used by most shops to cut good aluminium sheet into smaller pieces that more easily fit into the trash can after you cut on the inside of the line instead of the outside edge.
TWO-TON ENGINE HOIST:
A tool for testing the maximum tensile strength of everything you forgot to disconnect.
CRAFTSMAN 1/2 x 24-INCH SCREWDRIVER:
A very large pry bar that inexplicably has an accurately machined screwdriver tip on the end opposite the handle.
AVIATION METAL SNIPS:
See hacksaw.
PHILLIPS SCREWDRIVER:
Normally used to stab the vacuum seals under lids and for opening old-style paper-and-tin oil cans and splashing oil on your shirt; but can also be used, as the name implies, to strip out Phillips screw heads.
STRAIGHT SCREWDRIVER:
A tool for opening paint cans. Sometimes used to convert common slotted screws into non-removable screws.
PRY BAR:
A tool used to crumple the metal surrounding that clip or bracket you needed to remove in order to replace a 50 cent part.
HOSE CUTTER:
A tool used to make hoses too short.
HAMMER:
Originally employed as a weapon of war, the hammer nowadays is used as a kind of divining rod to locate the most expensive parts adjacent the object we are trying to hit.
MECHANIC'S KNIFE:
Used to open and slice through the contents of cardboard cartons delivered to your front door; works particularly well on contents such as seats, vinyl records, liquids in plastic bottles, collector magazines, refund checks, and rubber or plastic parts. Especially useful for slicing work clothes, but only while in use.
DAMMIT TOOL:
Any handy tool that you grab and throw across the garage while yelling "DAMMIT" at the top of your lungs. It is also, most often, the next tool that you will need.
__________________
Reply With Quote
The Following 2 Users Say Thank You to weemo05 For This Useful Post:
manictaz (12-11-2008), Marbles (12-11-2008)
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Common Tools Defined manictaz Jokes & Humor 0 11-30-2008 10:48 AM
the late Mr. Common Sense manictaz Writers Block 1 01-16-2008 12:54 PM
Tools and their proper uses... manictaz Jokes & Humor 0 12-02-2007 07:06 AM
uuugghhhhh SeXyOnE The Whiner Line 25 06-05-2007 11:24 PM
Common Sense (so True) dewey Writers Block 1 02-16-2007 09:19 AM


All times are GMT -4. The time now is 08:13 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
© 2002 - 2010 BN Media, LLC